Updated November 2026
A Craftsman lawn mower that runs fine, shuts off, and then refuses to restart usually has one of a handful of common faults. The problem is most often fuel delivery, spark, or airflow, and you can check all three with basic tools in about an hour. This guide walks through the checks in the order that solves the most problems fastest.
Start With the Fuel System
Stale gas is the most frequent cause of a mower that quits and won’t come back. Gasoline can break down in as little as 30 days, leaving varnish that clogs the carburetor jets. Drain the old fuel, add fresh regular unleaded (ideally 87 octane with no more than 10% ethanol), and try again. If the mower still cranks but won’t fire, the carburetor is the next suspect.
Shopping for one? See our guide: Lawn Mower Won't Start After Running Out of Gas: 3 Best Starting Aids Compared.
- Check that the fuel shutoff valve (if equipped) is open.
- Inspect the fuel line for cracks, soft spots, or kinks.
- Remove the fuel filter in the line and check for debris or varnish.
- Confirm the gas cap vent is not clogged, since a blocked vent can starve the engine of fuel.
Check the Spark Plug and Ignition
If the engine turns over but doesn’t fire, the spark plug is the next thing to test. Remove the plug, inspect the electrode, and look for heavy black carbon, oil fouling, or a worn gap. Manufacturers typically specify a gap in the range of 0.030 inches for many small engines, so check your owner’s manual for the exact figure. Replace the plug if it looks worn, and reconnect the boot firmly.
A weak or failed ignition coil can also cause a no-start after running, especially if the mower gets hot. Engines often stop firing once the coil warms up and then recover after cooling, which points to a coil problem. Testing a coil properly requires a multimeter, so if you are not comfortable with electrical testing, a small engine repair shop can do it quickly.
Clear the Air Filter and Carburetor
Airflow problems can cause a mower to stall under load and then refuse to restart. Remove the air filter and inspect it. A paper filter should be replaced when it is clogged, and a foam filter can usually be washed and re-oiled. A dirty or clogged air filter forces the engine to run rich, which fouls the plug and causes hard starting.
If the fuel and spark checks come back clean, the carburetor may need cleaning. Remove it, spray the jets with carburetor cleaner, and clear any small passages with a fine wire. A rebuild kit replaces the gaskets and diaphragms that often fail first.
Recommended gear
- A digital multimeter lets you test ignition coil resistance and confirm whether power is reaching the plug. View on Amazon
- A carburetor cleaner spray helps dissolve varnish from jets and passages without tearing down the entire carburetor. View on Amazon
- A spark plug socket and gap tool makes plug removal and gap checks quick and reduces the risk of cracking the porcelain. View on Amazon
Common mistakes
- Pouring fresh gas into a tank full of old gas, which does not fully fix a varnish problem.
- Over-tightening the spark plug, which can damage the threads in the cylinder head.
- Ignoring the air filter until the engine is already running poorly.
- Assuming the battery is the cause on a gas mower that uses only a recoil start or electric start circuit; check the spark first.
FAQ
Why does my Craftsman mower start cold but die after running?
This usually points to a fuel delivery problem, such as a partially clogged carburetor jet or a weak fuel pump on models that use one. The engine has enough fuel to start but runs out or loses pressure once it warms up.
How long can gas sit in a Craftsman mower before it goes bad?
Gasoline can start to degrade within about 30 days, and older fuel is a common cause of hard starting. Adding a fuel stabilizer or running the engine dry before storage helps prevent the problem.
When should I take the mower to a repair shop?
If you have checked fuel, spark, and airflow and the engine still won’t start, or if you suspect an internal engine problem, take it to a qualified small engine technician. Consult a professional before opening the engine or testing high-voltage ignition parts if you are unsure.
Conclusion
Most Craftsman mowers that won’t restart after running are fixed by fresh fuel, a new spark plug, or a clean air filter. Work through fuel, spark, and airflow in that order, and you will usually find the fault quickly. If the problem persists after these checks, a professional diagnosis is the next step.
Related reading
- Riding Lawn Mower Won't Start After Running: 7 Causes and Fixes
- Lawn Mower Won't Start After Running for Awhile: 6 Fixes to Try First
- Lawn Mower Won't Start After Running Over Something: 7 Checks First
- John Deere Lawn Mower Won't Start After Running: 6 Checks to Make First
- Craftsman Riding Lawn Mower Won't Start After Sitting: 7 Fixes That Work
- Craftsman Lawn Mower Won't Start After Sitting: 8 Fixes That Work

