Updated November 2026
A Craftsman lawn mower that starts fine when cold but refuses to fire up after it has been running is usually dealing with one of three problems: fuel that has turned to vapor, a spark that has weakened as the engine heats up, or an air or fuel delivery issue that worsens with temperature. This guide walks through how to narrow down the cause and fix it, starting with the simplest checks.
Confirm the Symptom Before You Start Troubleshooting
Hot-start problems have a recognizable pattern. The engine cranks normally, may even sputter, and then stops or fails to catch. If it starts cold, runs for a few minutes, shuts off, and then won’t restart until it cools for 20 to 30 minutes, you are almost certainly looking at heat-related fuel or ignition trouble. If the engine barely turns over at any temperature, the issue is more likely the battery, starter, or safety switches, and you should check What to Check When Lawn Mower Won't Start: 6 Steps Before You Call a Pro first.
Shopping for one? See our guide: Craftsman M220 Lawn Mower Won't Start: 7 Best Recoil Starter Replacements (2026).
Check for Fuel Vapor Lock
Vapor lock is the most common cause on Craftsman push mowers and riding models alike. Gasoline heats in the carburetor bowl and fuel line, forms vapor bubbles, and the carburetor can no longer draw liquid fuel. Start by inspecting the fuel line for cracks or hardening and confirming the fuel shutoff is fully open. Stale or low-octane fuel vaporizes more readily, so drain old fuel and refill with fresh gasoline. Many owners find that a fuel stabilizer and a tank kept at least half full reduce the problem noticeably.
Inspect the Spark Plug and Ignition
A spark plug that is fouled, worn, or has the gap set incorrectly can run fine cold and fail once the engine is hot. Remove the plug, check the electrode for carbon buildup or oil, and measure the gap against the value in your owner’s manual. Replace the plug if the electrode is eroded or the insulator is cracked. Also check the kill switch wire and the boot on the plug, since a loose connection can cause intermittent spark that gets worse under heat. For a deeper look, Seasonal Lawn Edge Care: What to Do and When covers this in detail.
Quick ignition checklist
- Remove the spark plug boot and inspect for cracks.
- Pull the plug and check color and deposits.
- Set the gap to the manufacturer’s specification.
- Reinstall with the boot firmly seated.
Look at Air Flow and the Carburetor
A dirty air filter causes the engine to run rich, and a rich mixture can flood the cylinder when hot. Clean or replace the foam or paper filter and check that the air intake is not blocked by grass clippings. Next, inspect the carburetor for varnish. Old fuel leaves residue in the jets that restricts flow, which matters more as the engine warms. A carburetor cleaner and a careful rebuild kit can restore proper operation, but if you are not comfortable taking the carb apart, a shop can handle it.
Consider Cooling and Engine Health
Cooling fins packed with grass and dirt trap heat, which makes every other problem worse. Clear the fins and the shrouding around the engine, and confirm the blower housing is intact. If the mower has been running hot for a long time, compression may be dropping due to worn rings or valves. A compression check is a useful diagnostic step when the basics are all in order. Keep in mind that work involving fuel systems and high-voltage ignition carries fire and injury risk, so consult a qualified small-engine technician if you are unsure.
Recommended gear
A basic set of spark plug tools, including a gap gauge and a socket that fits your plug, makes ignition checks quick. A fuel stabilizer helps prevent vapor and varnish problems between uses. A carburetor cleaner spray is useful for clearing jets when you suspect residue.
Common mistakes
- Assuming the starter is bad when the real issue is fuel vapor.
- Reusing old gasoline that has lost its stability.
- Overlooking a loose spark plug boot that only fails when the engine heats.
- Skipping the air filter because it looks clean on the outside.
- Hosing down a hot engine, which can crack components and does not fix fuel issues.
FAQ
Why does my Craftsman mower start cold but not after running?
Heat turns fuel in the carburetor and lines into vapor, and a weakened spark or dirty air filter makes it harder to restart. Checking fuel quality and the spark plug usually identifies the cause.
How long should I wait before restarting a hot mower?
Allow the engine to cool for roughly 20 to 30 minutes so the fuel system can settle. Restarting immediately often fails because of vapor in the lines.
Can old gas cause a hot-start problem?
Yes. Stale gasoline vaporizes more easily and leaves varnish in the carburetor, both of which contribute to heat-related starting failures.
Conclusion
Most hot-start failures on Craftsman mowers come down to fuel vapor, a worn spark plug, or restricted air flow. Work through fuel quality, ignition, and air intake before replacing major parts. If the problem persists after these steps, a small-engine technician can perform a compression check and carburetor service safely.

